A1000 1000W Subwoofer Amplifier Bundle with 2x 8" 1600W Peak Subs & Wiring Kit
The JBL Club A1000 mono subwoofer amplifier delivers 1000-Watts RMS using a Class D amplifier design to ensure high output and minimum current draw. Speaker-level inputs allow this amplifier to integrate into almost any system, even one using your car's factory radio. You can use the low-pass filter and variable bass boost to maximize the performance of your subwoofer and enclosure, while a phase switch ensures that the bass will blend well with your full-range speakers.
General Features:
- 600 watts RMS x 1 at 4 ohms (1000 watts RMS x 1 at 2 ohms)
- Class D amp technology
- frequency response: 10-320 Hz
- variable low-pass filter (32-320 Hz, 12 dB/octave)
- variable bass boost (0-12dB at 45Hz)
- phase switch (0, 180 degrees)
- wired remote level control included
- preamp inputs and outputs
- speaker-level inputs (speaker wire-to-RCA adapters included)
- 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- fuse rating: 35A x 3
- WxHxD=12-5/8” x 2-1/16" x7-1/8”
UPC Code 050036369183
Looking for a more moving audio experience? Take Infinity car audio for a ride. Innovative materials and breakthrough engineering have always put Infinity products out in front of the competition. This Kappa Series subwoofer features SSI (Selectable Smart Impedance), a HARMAN-exclusive impedance selector, that lets you choose a 2- or 4-ohm impedance at the flip of a switch. The proprietary aero-cooling design keeps the voice coil cool while optimizing power handling and longterm reliability. And, the acoustically damped glass-fiber cones have been engineered to minimize distortion and unwanted artifacts. More performance. More flexibility. You get both when you step up to a Kappa subwoofer.
General Features:
- 8" (200mm) high-performance car audio subwoofer
- Power Handling: 400W rms; 1600W Peak
- Sensitivity (@ 2.83V): 89dB
- Frequency Response: 34Hz - 200Hz
- Voice Coil Diameter: 2" (51mm)
- Impedance: 2 or 4 ohms, switch selectable
- SSI (Selectable Smart Impedance)
- Oversized aero-cooled voice coil
- Acoustically damped glass-fiber cone
- Premium screw-down terminals
DO NOT USE DRILLS ON THE SCREW SPEAKER TERMINALS EVER.
Loosen and Tighten BY HAND ONLY. Using a Drill snaps the solder connection on the back of the terminal and the X-over (coax) Circuit board.
UPC Code 050667373979
The Enrock 8-Gauge Amplifier Installation Kit makes installing your brand new sound system in your car or truck much easier. It includes all of the cables, wires, tubing, ties, grommets and ring terminals that you will need in order to get your new sound system up and running.
The car amp install kit works with a wide range of sound systems and car types and it makes the installation process much simpler by conveniently adding all your supplies to one single kit.
Kit Includes:
- 20 ft. 8 GA Red Power Cable.
- Competition High Quality Fuse Holder.
- 1/4" Ring Terminal.
- 3 ft. 8 GA Black Ground Cable #10 Ring Terminal.
- 16 ft. 18 GA Blue Turn-On Wire.
- 20 ft. High Performance RCA (TRCA) Interconnect (3) Rubber Grommets.
- 30 ft. Speaker Wire 5/16" Ring Terminal.
- 6 ft. Split Loom Tubing (20) 4" Wire Ties.
UPC Code 728120451105