NavAtlas BMA476BT 4-Channel Waterproof 300 Watts Peak Bluetooth Amplifier, 2 Pairs (QTY 4) of JBL Club Marine MS8W 8" Two-Way White Speakers, Amplifier Installation Wiring Kit

$863.99
$599.90
(You save $264.09 )
SKU:
BMA476BT-28W-A
UPC:
709016541452
Condition:
New
Weight:
13.08 LBS
Shipping:
Calculated at Checkout

Out of stock

NavAtlas BMA476BT 4-Channel Bluetooth Amplifier, 4x 8" White Speakers, Wire Kit

NavAtlas BMA476BT 4-Channel Waterproof 300 Watts Peak Power Bluetooth Amplifier




Take your sound system to the next level with the NavAtlas BMA476BT amplifier, which can pump out 75 watts RMS across 4 Channels, ensuring you'll hear your music in supreme quality. This amplifier can also be bridged into a 2-channel mode and so you can power a pair of speakers with 140 watts RMS each. This water-resistant amp fits almost anywhere and its Class D design will keep it cool and efficient! This amplifier features Bluetooth technology for additional media expandability.


General Features:

  • Bluetooth 4.0 Technology
  • Audio Streaming (A2DP, AVRCP)
  • Class D Digital Design
  • Waterproof (IP66)
  • MOSFET Power Supply
  • Low-Level Inputs (RCA)
  • Variable Gain Control
  • Built-In Crossover (35Hz - 250Hz)
  • Brdigeable Operation
  • 2 Ohm Stable Stereo Operation
  • Damping Factor <100
  • Fuse Rating: 30A
  • 75W RMS @ 4 Channels @ 4 Ohms
  • 98W RMS @ 4 Channels @ 2 Ohms
  • 140W RMS @ 2 Channels @ 4 Ohms (Brdiged)
  • Total Peak Power Output: 300W
  • Signal to Noise Ratio: 80dB
  • Frequency Response: 10Hz-35kHz
  • Dimensions: 1.5"x9"x3"(HxWxD)

UPC Code 827204111802
JBL Club Marine MS8W 8" (200mm) Two-Way Marine Audio Multi-Element Speakers (Pair, White) (x2)




These JBL Club Marine Speakers are ready to take on your next outdoor adventure. Engineered to withstand sun, salt, sea spray and wash downs, they feature sealed motor structure, UV resistant one-piece cast-polymer baskets, a sealed magnet and rubber surrounds. The polypropylene cone and balanced dome tweeter provide great bass, smooth highs and lots of output to ensure every note can be heard loud and clear.


General Features:

  • IPx5 Marine Rating
  • Cosmetic Appeal
  • Outdoor Performance
  • Product Value
  • Marine Design
  • One-Piece Polymer Basket
  • Grille-Mounted Tweeters
  • Rubber Surrounds
  • Weather-Resistant
  • Balanced Dome Tweeters
  • Designed for the Elements
  • Harman Standard Reliability Testing
  • Individually Voiced
  • Power Handling: 150W RMS, 450W peak
  • Sensitivity (@ 2.83V): 92dB
  • Frequency Response: 30Hz – 20kHz
  • Impedance: 4 ohms

UPC Code 050036346269
Renegade REN10KIT 10mm^2 Car Audio Complete Amplifier Installation Wiring Kit




Renegade REN10KIT 10mm^2 Car Audio Complete Amplifier Installation Wiring Kit

General Features:

  • 1 x 10 mm^2 Power Wire (red), flexible Strands (0,15 mm), 5 m
  • 1 x 10 mm^2 Ground Wire (grey), flexible Strands (0,15 mm), 0.8 m
  • 1 x RCA Stereo Audio Cable (blue), double shielded, 5 m
  • 1 x 0.5 mm^2 Remote Wire, 5 m
  • 1 x AGU Fuse Holder with 40 A ANL Fuse
  • Installation Kit

Installation Instructions:

  • Disconnect at first the negative ground connection from the vehicle’s battery.
  • Connect the GROUND CABLE (brown, 0.8m) with the ground terminal of the amplifier and a suitable GROUND contact point on the car chassis, with a maximum distance of 1 meter from the amplifier. Use the ringterminal for the GROUND contact point. Ensure that all paint or other insulation is removed from around the hole area.
  • Find a suitable position for the FUSE HOLDER next to the car battery’s PLUS POLE. The maximum distance should not be more than 30 cm. Please ensure, that you don’t damage any parts of the car, like the fuel tank, wires etc.
  • Cut off a part of the POWER CABLE (red, 5m) on one end, which has the same length like the distance from the battery’s PLUS POLE to the FUSE HOLDER (max. 30cm). Connect this part on the end without ringterminal with the FUSE HOLDER (without inserted fuse) and the other end to the battery’s PLUS POLE. Use for the connection the supplied ring terminals.
  • Lead one end of the POWER CABLE (red) from the car battery area through the car to the +12V terminal of the amplifier and connect it. Then connect the other end of the cable with the FUSE HOLDER at the suitable terminal.
  • Lead the RCA/CINCH CABLE pair with attached REMOTE WIRE from the HEAD UNIT through the car to the amplifier’s position. Then connect the RCA/CINCH plugs on one end with amplifier, and the other end with the HEAD UNIT RCA/CINCH outputs. Please observe the correct polarity of all connections.
  • Connect the one end of the attached REMOTE WIRE with the REMOTE/REM terminal of the HEAD UNIT and the other end with the REMOTE/REM terminal of the amplifier. This wire provides a turn on/turn off signal to the amplifier, when the HEAD UNIT is turned on / turned off. NOTE: some amplifier types may require, that you have to extend the REMOTE WIRE with a suitable cable, to lead the REMOTE WIRE to the other endpanel of the amplifier.
  • At least insert the FUSE into the FUSE HOLDER. Ensure not to cause a short circuit, or your car’s electric system may get damaged. Do not touch the bare metal parts of the cable or the car battery, otherwise a risk of electric shock consists. Then re-connect the negative ground connection to the vehicle’s battery.

UPC Code 854932002478

1 Year Manufacturer Warranty