Sony MEX-N4300BT Bluetooth Receiver, 4x 6.5" Speakers, 4-Channel Amp, Wiring Kit
Keep in touch on the road with Dual Bluetooth connectivity from the MEX-N4300BT. Wirelessly connect your first phone to play music, get directions and communicate with contacts. Add a second phone to make and receive hands-free calls from either phone. Built in 4x55W amplification delivers clear audio playback and plenty of volume. Use voice commands to get directions, play music, and communicate with contacts when connected with your smartphone. This receiver also features CD playback.
General Features:
- EXTRA BASS: Yes (1,2)
- DSO (DYNAMIC STAGE ORGANIZER): No
- OUTPUT POWER: 4 x 55W
- PRE OUT: Rear+Sub
- SUB OUT: Yes
- Front USB/AUX Input
- USB MEDIA TRANSFER PROTOCOL: Yes
- USB ANDROID OPEN ACCESSORY PROTOCOL : Yes (2.0)
- CD Player
- Voice Control Siri Eyes Free and Android
- Sound Synchronized Illumination
- High Pass/Low Pass Filter: 80/100/120
- High Voltage Pre Out: No
- Subwoofer Direct Connection
- 18FM/12AM Presets
- RDS: Yes
- Key Illumination: Yes
- LCD Display
- Built-In Microphone
UPC Code 027242911239
These Infinity Alpha 6530 6.5" speakers are the perfect addition to your vehicle's audio system to bring it to the next level. These speakers feature injection-molded polypropylene cones and have been comeptitively tuned to ensure elite quality sound and great sonic reproduction. With 290 watts of peak power, these speakers are ready to handle all your audio needs.
General Features:
- 6.5" 3-Way Coaxial Speakers
- Power Handling: 40W RMS, 290W Peak
- Injection-Molded Polypropylene Cone
- Competitively Tuned
- Frequency Response: 55Hz-20KHz
- Impedance: 4-Ohms
- Sensitivity (at 2. 83V): 91dB
- Mounting Depth: 2. 25"
UPC Code 050667373023
The JBL Club A754 amplifier features a low-profile chassis and a small overall footprint to fit in
more vehicles where available space is limited. Speaker-level and low-level inputs allow the Club A754 to integrate with both aftermarket and factory car stereo systems. Unlike many amplifiers available at similar prices, the JBL Club A754 features variable electronic crossovers for precise system tuning and performance.
The Club A754 has been engineered using Balanced Differential Inputs to ensure low noise
and distortion even at high output levels. This also makes it far less susceptible to line induced
engine noise. When low-level inputs are used, this control adjusts the input sensitivity between 200mVrms
and 2.0 Vrms. When high-level inputs are used, this control adjusts the input sensitivity between 2Vrms and 20Vrms.
On-board circuitry protects the Club A754 from shorts, high-temperature, overvoltage and
undervoltage. An LED indicator is provided to let you know when one of these conditions exists. Using multiple amplifiers, the Club A754 has full range preamp outputs allowing you to feed an
additional amplifier without using splitters.
The JBL Club A754 4 channels subwoofer amplifier delivers 400-Watts RMS using a Class H
amplifier design to ensure high output and minimum current draw. This switch changes DC to REM to adapt with low-level signals or high-level signals, this is especially helpful as part of remote turn-on lead of your installation more choice. A selectable “Turn-on mode” can protect battery to avoid current drain, when you don’t expect to turn on your amplifier.
General Features:
- 4 channel car amplifier
- 75 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms)
- 200 watts RMS x 2 at 4 ohms in bridged mode (4-ohm stable in bridged mode)
- Variable high- and low-pass filters (32–320Hz, 12dB/octave) on front and rear channels
- Preamp and speaker-level inputs
- Preamp outputs
- Fuse rating: 30A x 2
- 8-gauge power and ground leads
- recommended – wiring and hardware not included with amplifier
- Compact size
- High and low level input
- Variable crossover
- Low noise and distortion
- Input Level Control
- Full on-board protection
- Preamp Outputs
- Class H amp technology
- Turn-on mode
- W x H x D = 320mm x 51.3mm x 180mm
- W x H x D = 12-5/8" x 2-1/16" x 7-1/8"
UPC Code 050036369190
Renegade REN10KIT 10mm^2 Car Audio Complete Amplifier Installation Wiring Kit
General Features:
- 1 x 10 mm^2 Power Wire (red), flexible Strands (0,15 mm), 5 m
- 1 x 10 mm^2 Ground Wire (grey), flexible Strands (0,15 mm), 0.8 m
- 1 x RCA Stereo Audio Cable (blue), double shielded, 5 m
- 1 x 0.5 mm^2 Remote Wire, 5 m
- 1 x AGU Fuse Holder with 40 A ANL Fuse
- Installation Kit
Installation Instructions:
- Disconnect at first the negative ground connection from the vehicle’s battery.
- Connect the GROUND CABLE (brown, 0.8m) with the ground terminal of the amplifier and a suitable GROUND contact point on the car chassis, with a maximum distance of 1 meter from the amplifier. Use the ringterminal for the GROUND contact point. Ensure that all paint or other insulation is removed from around the hole area.
- Find a suitable position for the FUSE HOLDER next to the car battery’s PLUS POLE. The maximum distance should not be more than 30 cm. Please ensure, that you don’t damage any parts of the car, like the fuel tank, wires etc.
- Cut off a part of the POWER CABLE (red, 5m) on one end, which has the same length like the distance from the battery’s PLUS POLE to the FUSE HOLDER (max. 30cm). Connect this part on the end without ringterminal with the FUSE HOLDER (without inserted fuse) and the other end to the battery’s PLUS POLE. Use for the connection the supplied ring terminals.
- Lead one end of the POWER CABLE (red) from the car battery area through the car to the +12V terminal of the amplifier and connect it. Then connect the other end of the cable with the FUSE HOLDER at the suitable terminal.
- Lead the RCA/CINCH CABLE pair with attached REMOTE WIRE from the HEAD UNIT through the car to the amplifier’s position. Then connect the RCA/CINCH plugs on one end with amplifier, and the other end with the HEAD UNIT RCA/CINCH outputs. Please observe the correct polarity of all connections.
- Connect the one end of the attached REMOTE WIRE with the REMOTE/REM terminal of the HEAD UNIT and the other end with the REMOTE/REM terminal of the amplifier. This wire provides a turn on/turn off signal to the amplifier, when the HEAD UNIT is turned on / turned off. NOTE: some amplifier types may require, that you have to extend the REMOTE WIRE with a suitable cable, to lead the REMOTE WIRE to the other endpanel of the amplifier.
- At least insert the FUSE into the FUSE HOLDER. Ensure not to cause a short circuit, or your car’s electric system may get damaged. Do not touch the bare metal parts of the cable or the car battery, otherwise a risk of electric shock consists. Then re-connect the negative ground connection to the vehicle’s battery.
UPC Code 854932002478