Sony MEX-N4300BT CD Receiver, 4x 6x9" 3-Way Speakers, 5-Channel Amp, Wiring Kit
Keep in touch on the road with Dual Bluetooth connectivity from the MEX-N4300BT. Wirelessly connect your first phone to play music, get directions and communicate with contacts. Add a second phone to make and receive hands-free calls from either phone. Built in 4x55W amplification delivers clear audio playback and plenty of volume. Use voice commands to get directions, play music, and communicate with contacts when connected with your smartphone. This receiver also features CD playback.
General Features:
- EXTRA BASS: Yes (1,2)
- DSO (DYNAMIC STAGE ORGANIZER): No
- OUTPUT POWER: 4 x 55W
- PRE OUT: Rear+Sub
- SUB OUT: Yes
- Front USB/AUX Input
- USB MEDIA TRANSFER PROTOCOL: Yes
- USB ANDROID OPEN ACCESSORY PROTOCOL : Yes (2.0)
- CD Player
- Voice Control Siri Eyes Free and Android
- Sound Synchronized Illumination
- High Pass/Low Pass Filter: 80/100/120
- High Voltage Pre Out: No
- Subwoofer Direct Connection
- 18FM/12AM Presets
- RDS: Yes
- Key Illumination: Yes
- LCD Display
- Built-In Microphone
UPC Code 027242911239
These Clarion SE series speakers enable you to enjoy powerful, dynamic sound with stable performance over a broad range from highs to lows, all in a multiaxial speakers design.
MIPP Cone Woofer for Low Distortion and High-Speed Response. Polypropylene with mica particles blended in is used in this injection-moulded cone to attain superior response, making it ideal for factory upgrades. Strontium magnets have a magnetic flux density that is far higher than conventional ferrite magnets, enabling reproduction of dynamic bass sounds from a relatively small voice coil.
General Features:
- Music Peak Power (W) : 400
- Frequency Response (Hz) : 42 - 20 k
- Mounting Depth (mm) : 70
- 150 × 230 mm MIPP cone woofer
- Powerful strontium magnet for dynamic bass response
- Grille included
UPC Code 729218021606
This Dual 5-channel amplifier is marine-grade and rated IP66, making it the perfect amp system for open sound systems and open-environment applications. With a MOSFET power supply, Class D technology, and 600 watts of peak power, this amplifier will be sure to provide your system with the boost you need for impressive sound.
Class D Technology 5/4/3 Channels Waterproof
lP66 MOSFET power supply
4-Layerconfurmal coated PCB assembly
Variable gain control
Turn-On/Off muting drcuiby(soft mute)
Ground loop isolation input circuit and high-level speakerinp
Bass Boost Adjustment - 0-12d8@50Hz High Pass Crossover{12dB/0ct) - Variable 15-250Hz (FR/RR) - 20kHz Low Pass Crossover (12dB/Oct.) - Variable 35-250Hz (SUB) - 20kHz Fuses: 40A x 2 (ATC-type)
UPC Code 827204112205
Renegade REN10KIT 10mm^2 Car Audio Complete Amplifier Installation Wiring Kit
General Features:
- 1 x 10 mm^2 Power Wire (red), flexible Strands (0,15 mm), 5 m
- 1 x 10 mm^2 Ground Wire (grey), flexible Strands (0,15 mm), 0.8 m
- 1 x RCA Stereo Audio Cable (blue), double shielded, 5 m
- 1 x 0.5 mm^2 Remote Wire, 5 m
- 1 x AGU Fuse Holder with 40 A ANL Fuse
- Installation Kit
Installation Instructions:
- Disconnect at first the negative ground connection from the vehicle’s battery.
- Connect the GROUND CABLE (brown, 0.8m) with the ground terminal of the amplifier and a suitable GROUND contact point on the car chassis, with a maximum distance of 1 meter from the amplifier. Use the ringterminal for the GROUND contact point. Ensure that all paint or other insulation is removed from around the hole area.
- Find a suitable position for the FUSE HOLDER next to the car battery’s PLUS POLE. The maximum distance should not be more than 30 cm. Please ensure, that you don’t damage any parts of the car, like the fuel tank, wires etc.
- Cut off a part of the POWER CABLE (red, 5m) on one end, which has the same length like the distance from the battery’s PLUS POLE to the FUSE HOLDER (max. 30cm). Connect this part on the end without ringterminal with the FUSE HOLDER (without inserted fuse) and the other end to the battery’s PLUS POLE. Use for the connection the supplied ring terminals.
- Lead one end of the POWER CABLE (red) from the car battery area through the car to the +12V terminal of the amplifier and connect it. Then connect the other end of the cable with the FUSE HOLDER at the suitable terminal.
- Lead the RCA/CINCH CABLE pair with attached REMOTE WIRE from the HEAD UNIT through the car to the amplifier’s position. Then connect the RCA/CINCH plugs on one end with amplifier, and the other end with the HEAD UNIT RCA/CINCH outputs. Please observe the correct polarity of all connections.
- Connect the one end of the attached REMOTE WIRE with the REMOTE/REM terminal of the HEAD UNIT and the other end with the REMOTE/REM terminal of the amplifier. This wire provides a turn on/turn off signal to the amplifier, when the HEAD UNIT is turned on / turned off. NOTE: some amplifier types may require, that you have to extend the REMOTE WIRE with a suitable cable, to lead the REMOTE WIRE to the other endpanel of the amplifier.
- At least insert the FUSE into the FUSE HOLDER. Ensure not to cause a short circuit, or your car’s electric system may get damaged. Do not touch the bare metal parts of the cable or the car battery, otherwise a risk of electric shock consists. Then re-connect the negative ground connection to the vehicle’s battery.
UPC Code 854932002478