JBL Stage Marine 10" 600 Watt Max Power Gray Marine Audio Subwoofer (Single), 1200 Watt Max Power Mono Class D Boat Amplifier, 8 Gauge Amplifier Wiring Kit

---

This JBL Stage Marine Subwoofer is ready to take on your next outdoor adventure. This fully marinized spubwoofer not only delivers JBL sound, but it brings the sound to life. Engineered to withstand sun, salt, sea spray and wash downs, they feature sealed motor structure, UV resistant one-piece cast-polymer baskets and rubber surrounds. The polypropyelene cone provides great bass and lots of output to ensure low frequencies can be heard loud and clear.

General Features:

• IPx5 Rated
• Outdoor Performance
• Marine Design
• Balanced Dome Tweeters
• Rubber Surrounds
• Individually Voiced
• Harman Standard Reliability Tested
• Power Handling: 200Wrms, 600W peak
• Sensitivity (@ 2.83V): 88dB
• Frequency Response: 30Hz – 250Hz
• Nominal Impedance: 4 ohms

What's in the box?:

• 1 x Subwoofer with attached grille
• 1 x Stainless steel mounting hardware
• 1 x Drill bit for easy installation
• 1 x Foam gasket
• 1 x Subwoofer pigtail harness
• 2 x JBL sticker
• 1 x Quick Start Guide

UPC Code

---

Infinity's marine M6001A mono subwoofer amplifier delivers 600-Watts RMS to your subwoofer, and its Class D design ensures the amp's high output will put minimal strain your marine's electrical system. Speaker-level inputs allow this amplifier to work in almost any system, even if you're hanging on to your factory radio. You can use the low-pass filter and variable bass boost to maximize the performance of your subwoofer and enclosure, while a phase switch ensures that the bass will blend well with your full-range speakers.

General Features:

• Mono subwoofer Marine Amplifier
• 350 watts RMS x 1 at 4 ohms
• 600 watts RMS x 1 at 2 ohms
• 1200 Watts Peak Power
• Class D amp technology
• Variable bass boost
• RBC wired remote - volume adjustment
• Phase switch
• Preamp and speaker-level inputs
• Variable low-pass filter
• Fuse rating: 30A x 2
• 8-gauge power and ground leads recommended
• Wiring and hardware not included

UPC Code 050667380083

---

Power your marine amplifier with a wiring kit that can withstand the harsh environment and still deliver full sound performance. Fully tinned wiring ensures that these amp kits won’t corrode or oxidize and turn green after a season on the water. Oxygen-free copper provides a reliable connection with maximum conductivity. By using 100% virgin copper the tin won’t flake off, something commonly seen when using recycled copper materials. While it is also common to tin just the tips of the wire for cost savings, this practice does not actually provide any benefits. Metra’s amp kits use fully tinned copper wire from top to bottom that can withstand a harsh marine environment and salty air. The ignition-protected 50-amp circuit breaker is IP67 rated with stainless steel connection points for corrosion resistance

Amplifier Wiring Kit:

• Marine compliant amplifier wiring kit
• Fully tinned 100% virgin copper wire
• BC5W2 marine compliant jacket
• 50-amp marine circuit breaker is rated IP67 with stainless steel connection points for corrosion resistance
• Easy to solder tinned wiring
• Connectors, ring terminals, and wire ties included

What’s in the box:

• (1) 8-gauge tinned oxygen-free copper side-by-side red power and yellow ground wire (10ft.)
• (1) 18-gauge tinned oxygen-free copper blue remote turn-on wire (18ft.)
• (2) 8-gauge ring terminal with shrink tube and logo, pre-terminated on each end of the 2ft. red wire
• (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on 8ft. red wire
• (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on yellow wire
• (1) Ignition protected circuit breaker (50-amp)

UPC Code 086429416820