JBL Stage 1200S 12" 1000W Max Power Car Subwoofer, 400 Watt Mono Amplifier, Kit
The JBL Stage 1200S subwoofer enclosure pounds out resounding bass from a compact enclosure that fits in just about any vehicle. High efficiency combines with impressive power-handling for rich and satisfying performance. The 12" woofer cone and large voice coil work together for remarkable realism, note-perfect accuracy, and sustained bass response. And this enclosure's striking good looks are matched by its ease of installation.
General Features:
- 12" Sealed Subwoofer in Enclosure
- Power Handling: 250W RMS
- Power Handling: 1000W Peak
- Sensitivity: 91dB
- Frequency Response: 34Hz-200Hz
- Impedance: 2 ohms
UPC Code 050036381604
This CX-Series amp reaches massive power levels thanks to an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated look.
CX-Series Mono Amps are now one-ohm stable, giving you even more power and wiring options for your system! Using efficient Class-D power, the CXA400.1 features a variable bass boost with KickEQ, giving you as much as a 6dB of extra bump with a simple turn of the optional CXARC Remote Bass Controller. A powerful 12dB crossover and 24dB subsonic filter is included, letting you quickly tune your system to perfection. Use the full-range outputs to expand your system with other bass amps, or a full-range amp to complete your system.
CX.1 Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!
Expand your system with full-range, RCA pass-through outputs, then choose a “standard” mount or a cool vertical mount with the included hardware.
CX.1 Amps deliver as much as 400 watts into one bass channel.
General Features:
- Efficient Class-D amplifier
- Three-second turn-on/off delay to eliminate unwanted interference
- Variable 12dB crossovers provides control to dial in perfect sound
- KickEQ 6dB variable bass boost for those additional low frequencies
- 24dB subsonic filter for protection from potentially damaging frequencies
- FIT+ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
- Accepts up to 40-volt input signal
- Small footprint for easier installation
- Compatible with CXARC Remote Bass Control
- Vertical mounting hardware included for another unique look
- Power (watts/ch) 4 Ohm: 150x1
- Power (watts/ch) 2 Ohm: 300x1
- Power (watts/ch) 1 Ohm: 400x1
- CXRC Remote Bass Capable (sold sep.): yes
- Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L): 8-1/8, 20.6
- Frequency Response (Hz): 25-200, +0/-1dB
- Input Sensitivity:: 250mV-10V (Low Level), 1V-40V (High Level)
- Signal-to-Noise Ratio: >95dB, a-weighted, re: rated power
- Active Crossover: Variable Lo-pass 50Hz–200Hz, 12dB/octave
- Subsonic Filter: 25Hz @24dB/octave
- KickEQ Boost: Variable 0-6dB @40Hz
UPC Code 713034012788
Power your marine amplifier with a wiring kit that can withstand the harsh environment and still deliver full sound performance. Fully tinned wiring ensures that these amp kits won’t corrode or oxidize and turn green after a season on the water. Oxygen-free copper provides a reliable connection with maximum conductivity. By using 100% virgin copper the tin won’t flake off, something commonly seen when using recycled copper materials. While it is also common to tin just the tips of the wire for cost savings, this practice does not actually provide any benefits. Metra’s amp kits use fully tinned copper wire from top to bottom that can withstand a harsh marine environment and salty air. The ignition-protected 50-amp circuit breaker is IP67 rated with stainless steel connection points for corrosion resistance
Amplifier Wiring Kit:
- Marine compliant amplifier wiring kit
- Fully tinned 100% virgin copper wire
- BC5W2 marine compliant jacket
- 50-amp marine circuit breaker is rated IP67 with stainless steel connection points for corrosion resistance
- Easy to solder tinned wiring
- Connectors, ring terminals, and wire ties included
What’s in the box:
- (1) 8-gauge tinned oxygen-free copper side-by-side red power and yellow ground wire (10ft.)
- (1) 18-gauge tinned oxygen-free copper blue remote turn-on wire (18ft.)
- (2) 8-gauge ring terminal with shrink tube and logo, pre-terminated on each end of the 2ft. red wire
- (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on 8ft. red wire
- (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on yellow wire
- (1) Ignition protected circuit breaker (50-amp)
UPC Code 086429416820
