JBL A600 Class D Subwoofer Amplifier Bundle with 12” 1350W Max Sub & Wiring Kit
The JBL Club A600 amplifier features a low-profile chassis and a small overall footprint to fit in
more vehicles where available space is limited. Speaker-level and low-level inputs allow the Club A600 to integrate with both aftermarket and factory car stereo systems. Unlike many amplifiers available at similar prices, the JBL Club A600 features variable electronic crossovers and bass boost circuits allowing for precise system tuning and
performance.
The Club A600 has been engineered using Balanced Differential Inputs to ensure low noise
and distortion even at high output levels. This also makes it far less susceptible to line induced
radiated engine noise. When low-level inputs are used, this control adjusts the input sensitivity between 200mVrms and 2.0Vrms. When high-level inputs are used, this control adjusts the input sensitivity
between 2Vrms and 20Vrms.
On-board circuitry protects the Club A600 from shorts, high-temperature, overvoltage and undervoltage. An LED indicator is provided to let you know when one of these conditions exists. This switch changes the input phase to inverted or non-inverted. This is especially helpful as
part of system tuning based on the enclosure type and location in the vehicle.
The RBC wired remote is an easy installation and can be mounted for convenient volume
adjustment from driver’s seat.
The JBL Club A600 mono subwoofer amplifier delivers 600-Watts RMS using a Class D
amplifier design to ensure high output and minimum current draw.
This switch changes DC to REM to adapt with low-level signals or high-level signals, this is especially
helpful as part of remote turn-on lead of your installation more choice. A selectable “Turn-on mode”
can protect battery to avoid current drain, when you don’t expect to turn on your amplifier.
General Features:
- Mono subwoofer car amplifier
- 350 watts RMS x 1 at 4 ohms (600 watts RMS x 1 at 2 ohms)
- Class D amp technology
- Variable low-pass filter (32–320 Hz, 12 dB/octave)
- Variable bass boost (0-12dB at 45Hz)
- Phase switch (0, 180 degrees)
- Preamp and speaker-level inputs
- Fuse rating: 30A x 2
- 8-gauge power and ground leads
- recommended — wiring and hardware not included with amplifier
- Compact size
- High and low level input
- Variable crossover and bass boost
- Low noise and distortion
- Input Level Control
- Full on-board protection
- Phase Switch
- RBC wired remote
- W x H x D = 220mm x 51.3mm x 180mm
- W x H x D = 8-11/16" x 2-1/16" x 7-1/8"
UPC Code 050036369176
The JBL Stadium 122SSI 12" component subwoofer is the high-performance bass machine you need to take your audio system to the next level. This subwoofer can pump out 1350 watts of peak power and 450 watts of RMS power for an impressive sonic output. A switch which lets you vary the sub's impedance from 2 ohms to 4 ohms to optimize its effectiveness.
General Features:
- 450 watts RMS (1350 watts peak)
- 12" high-performance car subwoofer
- Glass fiber/paper pulp composite cone
- Nitrile rubber surround
- Stamped steel vented basket
- SSI (Selectable Smart Impedance): 2 or 4 ohms switchable
- Grille not included
UPC Code 050036381185
The Enrock 8-Gauge Amplifier Installation Kit makes installing your brand new sound system in your car or truck much easier. It includes all of the cables, wires, tubing, ties, grommets and ring terminals that you will need in order to get your new sound system up and running.
The car amp install kit works with a wide range of sound systems and car types and it makes the installation process much simpler by conveniently adding all your supplies to one single kit.
Kit Includes:
- 20 ft. 8 GA Red Power Cable.
- Competition High Quality Fuse Holder.
- 1/4" Ring Terminal.
- 3 ft. 8 GA Black Ground Cable #10 Ring Terminal.
- 16 ft. 18 GA Blue Turn-On Wire.
- 20 ft. High Performance RCA (TRCA) Interconnect (3) Rubber Grommets.
- 30 ft. Speaker Wire 5/16" Ring Terminal.
- 6 ft. Split Loom Tubing (20) 4" Wire Ties.
UPC Code 728120451105
