Controller:
- Control volume +/-, track FWD/PREV, PLAY/PAUSE, and auxiliary input
- Control the volume of 3 zones independently
- LED backlit controller
- Equipped with Bluetooth wireless technology
- Supports APTX-HD, APTX, APTX-X Low Latency, SBC, and ACC audio formats
- 24-bit lossless audio processor
- Rated IPX7 for powersports & marine applications
- Switch between Bluetooth wireless technology & auxiliary inputs
- Amplifier remote turn-on output
- (3) 4V 2-channel RCA outputs
- Frequency range: 18Hz to 25KHz
- Bluetooth wireless technology range: 35ft
- Input voltage: 12V-24V
Speakers:
- Power Handling: 100 watts RMS, 300 watts peak power
- Sensitivity: 92dB at 2.83 volts
- Frequency Response: 40 - 25kHz
- Voice Coil Diameter: 1 in. (25.5mm)
- Impedance: 3 ohm impedance
- Plus One Woofer Cones
- Perimeter RGB Illumination
- One Piece Polymer Basket
- Mylar Tweeters
- Harman Standard Reliability Testing
DO NOT USE DRILLS ON THE SCREW SPEAKER TERMINALS EVER.
Loosen and Tighten BY HAND ONLY. Using a Drill snaps the solder connection on the back of the terminal and the X-over (coax) Circuit board.
4-Channel Amplifier:
- Ultra-Compact Aluminum Chassis
- Conformal Coated PCB
- Big Dynamic Power
- Full-Range Outputs and Selectable Crossovers
- High and low level Inputs
- Max Power: 450W peak
- RMS Power Output @ 4O: 45W x 4, <1% THD+N
- Selectable hi-pass filter: off, 60-, 80-, 120Hz @ 12dB/octave
- Frequency Response: 20Hz – 20kHz
- Signal-to-Noise Ratio: >75dB (ref 1W output @ 4O)
- Fuse rating: 15A
2-Channel Amplifier:
- Max Power: 750W peak
- RMS Power Output @ 2Ω (full-range): 150W x 2, <1% THD+N
- RMS Power Output @ 4Ω (full-range): 100W x 2, <1% THD+N
- RMS Power Output @ 4Ω Bridged (full-range): 300W x 1, <1% THD+N
- Selectable all-/hi-/lo-pass filter: 60-, 80-, 120Hz @ 12dB/octave
- Selectable bass boost: 0-, 6-, 12dB @45Hz
- Frequency Response: 20Hz – 20kHz
- Signal-to-Noise Ratio (full-range): >75dB (ref 1W output @ 4Ω)
- Fuse rating: 25A
- Ultra-compact Aluminum Chassis
- Conformal-Coated PCB
- Big Dynamic Power
- Full-Range Outputs and Selectable
- Crossovers
- High- and low-level inputs
- Harman Standard Reliability Testing
- JBL Industrial Design
Amplifier Install Kit:
- Marine compliant amplifier wiring kit
- Fully tinned 100% virgin copper wire
- BC5W2 marine compliant jacket
- 50-amp marine circuit breaker is rated IP67 with stainless steel connection points for corrosion resistance
- Easy to solder tinned wiring
- Connectors, ring terminals, and wire ties included
What’s in the box:
- (1) 8-gauge tinned oxygen-free copper side-by-side red power and yellow ground wire (10ft.)
- (1) 18-gauge tinned oxygen-free copper blue remote turn-on wire (18ft.)
- (2) 8-gauge ring terminal with shrink tube and logo, pre-terminated on each end of the 2ft. red wire
- (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on 8ft. red wire
- (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on yellow wire
- (1) Ignition protected circuit breaker (50-amp)
1 Year Manufacturer Warranty
