2x JBL Club 10 10" 900 Watt Max Power High-Performance RGB LED Marine Audio Subwoofer with Grilles, 350 Watt x 1 @ 4 Ohms Mono Class D Boat Amplifier, 8 Gauge Amplifier Wiring Kit

---

JBL Club Marine Speakers are ready for your next outdoor adventure. These fully marinized speakers not only deliver JBL sound, they also provide RGB lighting to bring the sound to life. Engineered to withstand sun, salt, sea spray and wash downs, they feature sealed motor structures, UV resistant one-piece cast-polymer baskets, a sealed magnet and rubber surrounds.

The polypropyelene cone and balanced silk dome tweeter provide great bass, smooth highs and lots of output to ensure every note can be heard loud and clear. With two grille colors included in the box, you can easily match your speaker grilles with your boat.

Club Marine 10" Subwoofer

• Power Handling: 300Wrms, 900W peak
• Sensitivity (@ 2.83V): 89dB
• Frequency Response: 25Hz – 500Hz
• Nominal Impedance: 4ohm
• 1x Subwoofer
• 1x Speaker Grilles, Gloss White
• 1x Speaker Grilles, Satin Grey
• Stainless steel mounting hardware
• Drill bit for easy installation
• Foam gasket
• 1x Speaker Pigtail Harness
• 1x RGB Pigtail Harness
• 2x JBL sticker
• Quick Start Guide

UPC Code 050036390453

---

The JBL Marine A600 mono subwoofer amplifier delivers 600-Watts RMS using a Class D amplifier design to ensure high output and minimum current draw. Speaker-level inputs allow this amplifier to integrate into almost any system, even one using your Marine’s factory radio. You can use the low-pass filter and variable bass boost to maximize the performance of your subwoofer and enclosure, while a phase switch ensures that the bass will blend well with your full-range speakers.

General Features:

• Mono subwoofer Marine amplifier
• 350 watts RMS x 1 at 4 ohms (600 watts RMS x 1 at 2 ohms)
• Max Power 1200 watts
• Class D amp technology
• Variable low-pass filter (32-320 Hz, 12 dB/octave)
• Variable bass boost (0-12 dB at 45Hz)
• Phase switch (0, 180 degrees)
• Preamp and speaker-level inputs
• Fuse rating: 30A x 2
• 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
• WxHxD=220mm x 51.3mm x 180mm WxHxD=8-11/16” x 2-1/16” x7-1/8”

UPC Code 050036396929

---

Power your marine amplifier with a wiring kit that can withstand the harsh environment and still deliver full sound performance. Fully tinned wiring ensures that these amp kits won’t corrode or oxidize and turn green after a season on the water. Oxygen-free copper provides a reliable connection with maximum conductivity. By using 100% virgin copper the tin won’t flake off, something commonly seen when using recycled copper materials. While it is also common to tin just the tips of the wire for cost savings, this practice does not actually provide any benefits. Metra’s amp kits use fully tinned copper wire from top to bottom that can withstand a harsh marine environment and salty air. The ignition-protected 50-amp circuit breaker is IP67 rated with stainless steel connection points for corrosion resistance

Amplifier Wiring Kit:

• Marine compliant amplifier wiring kit
• Fully tinned 100% virgin copper wire
• BC5W2 marine compliant jacket
• 50-amp marine circuit breaker is rated IP67 with stainless steel connection points for corrosion resistance
• Easy to solder tinned wiring
• Connectors, ring terminals, and wire ties included

What’s in the box:

• (1) 8-gauge tinned oxygen-free copper side-by-side red power and yellow ground wire (10ft.)
• (1) 18-gauge tinned oxygen-free copper blue remote turn-on wire (18ft.)
• (2) 8-gauge ring terminal with shrink tube and logo, pre-terminated on each end of the 2ft. red wire
• (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on 8ft. red wire
• (1) 8-gauge ring terminal with shrink tube and logo, pre-terminated on yellow wire
• (1) Ignition protected circuit breaker (50-amp)

UPC Code 086429416820